Search Results

Diesel combustion and emissions formation is largely spray and mixing controlled and hence understanding spray parameters, specifically vaporization, is key to determine the impact of fuel injector operation and nozzle design on combustion and emissions. In this study, an eight-hole common rail piezoelectric injector was tested in an optically accessible constant volume combustion vessel at charge gas conditions typical of full load boosted engine operation. Liquid penetration of the eight sprays was determined via processing of images acquired from Mie back scattering under vaporizing conditions by injecting into a charge gas at elevated temperature with 0% oxygen. Conditions investigated included a charge temperature sweep of 800 to 1300 K and injection pressure sweep of 1034 to 2000 bar at a constant charge density of 34.8 kg/m₃.

The passive oxidation of particulate matter (PM) in a diesel catalyzed particulate filter (CPF) was investigated in a series of experiments performed on two engines. A total of ten tests were completed on a 2002 Cummins 246 kW (330 hp) ISM and a 2007 Cummins 272 kW (365 hp) ISL. Five tests were performed on each engine to determine if using engine technologies certified to different emissions regulations has an impact on the passive oxidation characteristics of the PM. A new experimental procedure for passive oxidation testing was developed and implemented for the experiments. In order to investigate the parameters of interest, the engines were initially operated at a steady state loading condition where the PM concentrations, flow rates, and temperatures were such that the accumulation of PM within the CPF was obtained in a controlled manner. This engine operating condition was maintained until a CPF PM loading of 2.2 ±0.2 g/L was obtained.

Increasing fuel injection pressure has enabled reduction of diesel emissions while retaining the advantage of the high thermal efficiency of diesel engines. With production diesel injectors operating in the range from 300 to 2400 bar, there is interest in injection pressures of 3000 bar and higher for further emissions reduction and fuel efficiency improvements. Fundamental understanding of diesel spray characteristics including very early injection and non-vaporizing spray penetration is essential to improve model development and facilitate the integration of advanced injection systems with elevated injection pressure into future diesel engines. Studies were conducted in an optically accessible constant volume combustion vessel under non-vaporizing conditions. Two advanced high pressure multi-hole injectors were used with different hole diameters, number of holes, and flow rates, with only one plume of each injector being imaged to enable high frame rate imaging.

Ducted fuel injection (DFI), a concept that utilizes fuel injection through ducts, was implemented in a constant pressure High Temperature Pressure Vessel at 60 bar ambient pressure, 800-1000 K ambient temperature, and 21 % oxygen. The ducts were 14 mm long and placed 3-4.7 mm from the orifice exit. The duct diameters ranged from 1.6-3.2 mm and had a rounded inlet and a tapered outlet. Diesel fuel was used in single-orifice fuel injectors operating at 250 MPa rail pressure. The objective of this work was to study soot reduction for various combinations of orifice and duct diameters. A complete data set was taken using the 150 μm orifice. A smaller data set was acquired for a 219 μm orifice, showing similar trends. Soot reduction peaked at an optimal duct diameter of 2-2.25 mm, corresponding to an 85-90 % spray area reduction for the 150 μm orifice. Smaller or larger duct diameters were less effective. Duct diameter had a minimal effect on ignition delay.

The paper describes an experimental activity on the spatial and temporal liquid- and vapor-phase distributions of diesel fuel at engine-like conditions. The influence of the k-factor (0 and 1.5) of a single-hole axial-disposed injector (0.100 mm diameter and 10 L/d ratio) has been studied by spraying fuel in an optically-accessible constant-volume combustion vessel. A high-speed imaging system, capable of acquiring Mie-scattering and Schlieren images in a near simultaneous fashion mode along the same line of sight, has been developed at the Michigan Technological University using a high-speed camera and a pulsed-wave LED system. The time resolved pair of schlieren and Mie-scattering images identifies the instantaneous position of both the vapor and liquid phases of the fuel spray, respectively. The studies have been performed at three injection pressures (70, 120 and 180 MPa), 23.9 kg/m3 ambient gas density and 900 K gas temperature in the vessel.

Spray angle and penetration length data were taken under cold start conditions for a Direct Injection Spark Ignition engine to investigate the effect of transient conditions on spray development. The results show that during cold start, spray development depends primarily on fuel pressure, followed by Manifold Absolute Pressure (MAP). Injection frequency had little effect on spray development. The spray for this single hole, pressure-swirl fuel injector was characterized using high speed imaging. The fuel spray was characterized by three different regimes. Regime 1 comprised fuel pressures from 6 - 13 bar, MAPs from 0.7 - 1 bar, and was characterized by a large pre-spray along with large drop sizes. The spray angle and penetration lengths were comparatively small. Regime 2 comprised fuel pressures from 30 - 39 bar and MAPs from 0.51 - 0.54 bar. A large pre-spray and large drop sizes were still present but reduced compared to Regime 1.

A gradient-based optimization tool has been developed and, in conjunction with a CFD code, utilized in the search of optimal fuel injection strategies. The approach taken uses a steepest descent method with an adaptive cost function, where the line search is performed with a fast-converging backtracking algorithm. The adaptive cost function is based on the penalty method, where the penalty coefficient is increased after every line search. The parameter space is normalized and, thus, the optimization occurs over the unit cube in higher-dimensional space. The application of this optimization tool is demonstrated for a non-road version of the Sulzer S20 DI diesel engine which, for these simulations, is equipped with a multi-orifice, asynchronous injection system. This system permits an independent timing of the fuel pulses, and each orifice has its own diameter and injection direction.

Passive regeneration (oxidation of particulate matter without using an external energy source) of particulate filters in combination with active regeneration is necessary for low load engine operating conditions. For low load conditions, the exhaust gas temperatures are less than 250°C and the PM oxidation rate due to passive regeneration is less than the PM accumulation rate. The objective of this research was to experimentally investigate active regeneration of a catalyzed particulate filter (CPF) using diesel fuel injection in the exhaust gas after the turbocharger and before a diesel oxidation catalyst (DOC) and to collect data for extending the MTU 1-D 2-layer model to include the simulation of active regeneration. The engine used in this study was a 2002 Cummins ISM turbo charged 10.8 L heavy duty diesel engine with cooled EGR. The exhaust after-treatment system consisted of a Johnson Matthey DOC and CPF (a CCRT®).

Recently, outboard engine technology has advanced significantly. With these new technologies comes a substantial improvement in emissions compared to traditional carbureted two-stroke engines. Some two-stroke gasoline direct injection (GDI) marine outboard engines are now capable of meeting California Air Resources Board 2008 Ultra-Low emissions standards. With improvement of gaseous emissions, studies are now being conducted to assess particulate matter (PM) emissions from all new technology marine outboard engines which include both four-stroke and two-stroke designs. Methods are currently being developed to determine the best way to measure PM from outboard engines. This study assesses gaseous and PM emissions, mutagenic activity of PM and oil consumption of two different technologies over the useful life of the engines.

With stringent emission regulations, aftertreatment systems with a Diesel Particulate Filter (DPF) and a Selective Catalytic Reduction (SCR) are required for diesel engines to meet PM and NOx emissions. The adoption of aftertreatment increases the back pressure on a typical diesel engine and makes engine calibration a complicated process, requiring thousands of steady state testing points to optimize engine performance. When configuring an engine to meet Tier IV final emission regulations in the USA or corresponding Stage IV emission regulations in Europe, this high back pressure dramatically impacts transient performance. The peak NOx, smoke and exhaust temperature during a diesel engine transient cycle, such as the Non-Road Transient Cycle (NRTC) defined by the US Environmental Protection Agency (EPA), will in turn affect the performance of the aftertreatment system and the tailpipe emissions level.

The necessity to study spray-wall interaction in internal combustion engines is driven by the evidence that fuel sprays impinge on chamber and piston surfaces resulting in the formation of wall films. This, in turn, may influence the air-fuel mixing and increase the hydrocarbon and particulate matter emissions. This work reports an experimental and numerical study on spray-wall impingement and liquid film formation in a constant volume combustion vessel. Diesel and n-heptane were selected as test fuels and injected from a side-mounted single-hole diesel injector at injection pressures of 120, 150, and 180 MPa on a flat transparent window. Ambient and plate temperatures were set at 423 K, the fuel temperature at 363 K, and the ambient densities at 14.8, 22.8, and 30 kg/m3. Simultaneous Mie scattering and schlieren imaging were carried out in the experiment to perform a visual tracking of the spray-wall interaction process from different perspectives.

Numerical modeling of fuel injection in internal combustion engines in a Lagrangian framework requires the use of a spray-wall interaction sub-model to correctly assess the effects associated with spray impingement. The spray impingement dynamics may influence the air-fuel mixing and result in increased hydrocarbon and particulate matter emissions. One component of a spray-wall interaction model is the splashed mass fraction, i.e. the amount of mass that is ejected upon impingement. Many existing models are based on relatively large droplets (mm size), while diesel and gasoline sprays are expected to be of micron size before splashing under high pressure conditions. It is challenging to experimentally distinguish pre- from post-impinged spray droplets, leading to difficulty in model validation.

To meet future NO, heavy-duty diesel emissions standards, exhaust gas recirculation (EGR) technology is likely to be used. To improve fuel economy and further lower emissions, the recirculated exhaust gas needs to be cooled, with the possibility that cooling of the exhaust gas may form sulfuric acid condensate in the EGR cooler. This corrosive condensate can cause EGR cooler failure and consequentially result in severe damage to the engine. Both a literature review and a preliminary experimental study were conducted. In this study, a manually controlled EGR system was installed on a 1995 Cummins Ml l-330E engine which was operated at EPA mode 9* (1800 rpm and 75% load). The Goksoyr-Ross method (1)** was used to measure the particle-phase sulfate and vapor-phase H2SO4 and SO2 at the inlet and outlet locations of the EGR cooler, obtaining H2SO4 and SO2 concentrations. About 0.5% of fuel sulfur in the EGR cooler was in the particle-phase.

Electronics technology has evolved significantly since the first electronically controlled heavy duty on-highway truck engines were introduced in the mid 1980's. Engine control hardware, software, and sensor designs have been driven by many factors. Emissions regulations, fuel economy, engine performance, operator features, fleet management information, diagnostics, vehicle integration, reliability, and new electronics technology are some of those factors. The latest engine electronics technology is not only found in heavy duty on-highway trucks, but in off-highway applications as well. Track-type tractors, haul trucks, wheel loaders, and agricultural tractors now benefit from the advantages of electronic engines. And, many more new applications are being developed.

Caterpillar Inc. has developed a new diesel engine fuel system, powered by hydraulics and controlled electronically. This Hydraulic Electronic Unit Injector, (HEUI), requires no mechanical actuating or mechanical control devices, and offers many advantages over conventional fuel injection systems. Inherent features of the HEUI Fuel System include injection pressure control independent of engine load or speed, totally flexible injection timing, and full electronic control of injection parameters. Packaging the HEUI Fuel System on an engine is simple, as the injector is compact and available in a variety of configurations. The hydraulic actuating circuit is straightforward, using lubricating oil from the engine sump. Hydraulic lines may be internal to the engine or external. This paper describes the Caterpillar HEUI Fuel System, its operating features, performance advantages, and application to diesel engines.

Diesel engine manufacturers have been asking for new, innovative, flexible fuel injection systems in order to meet future diesel engine emission requirements throughout the world and improve engine performance. Engineers at Caterpillar have listened to these requests and developed a fuel system concept to meet their needs. This new fuel system is called the Next Generation Electronic Unit Injector (NGEUI). The new concept is adaptable to mechanically actuated electronic unit injector, hydraulic electronic unit injector, electronic unit pump, and pump/line/nozzle systems. Features of the new fuel system are listed below: 1. Fully controllable injection pressure independent of engine speed and load 2. Injection pressure capability to 207 MPa (30,000 psi) 3. Reduced drive train torsional excitation and improved hydraulic efficiency 4.

This paper identifies potential performance benefits and computational costs of applying advanced multivariable control theory concepts to coordinate the control of a general multi-degree-of-freedom fuel system. The control variables are injection duration and pressure. The focus is on the design of a robust multi-input multi-output controller using H-infinity and mu synthesis methodology to coordinate the control of injection duration and pressure; reduce overshoots and system sensitivity to parameter variations caused by component aging. Model reduction techniques are used to reduce the order of the H-infinity controller to make it practically implementable. Computer simulation is used to test the robust performance of a generic engine and fuel system model controlled by the reduced order H-infinity controller and a traditional proportional plus integral controller.

A test stand was developed to evaluate an 11.5 cc, two-stroke, internal combustion engine in anticipation of future combustion system modifications. Detailed engine testing and analysis often requires complex, specialized, and expensive equipment, which can be problematic for research budgets. This problem is compounded by the fact that testing “micro” engines involves low flow rates, high rotational speeds, and compact dimensions which demand high-accuracy, high-speed, and compact measurement systems. On a limited budget, the task of developing a micro-engine testing system for advanced development appears quite challenging, but with careful component selection it can be accomplished. The anticipated engine investigation includes performance testing, fuel system calibration, and combustion analysis. To complete this testing, a custom test system was developed.

Today's advanced technology engines have a high content of electronic actuation requiring sophisticated real-time embedded software sensing and control. To enable research on such engines, a system with a flexible engine control unit (ECU) that can be rapidly configured and programmed is desired. Such a system is being used in the Advanced Internal Combustion Engine (AICE) Laboratories at Michigan Tech University (MTU) for research on a multi-cylinder spark-ignited gasoline, a high pressure common rail diesel and a single cylinder alternative fuels research engine. The system combines a production ECU with a software development system utilizing Mathworks Simulink/Stateflow © modeling tools. The interface in the Simulink modeling environment includes a library of modeling and interface blocks to the production Operating System (OS), Low Level Drivers (LLD) and CAN-based calibration tool.

The Environmental Protection Agency (EPA) has published new emissions standards for snowmobiles, Federal Register 40 CFR, “Control of Emissions from Non-road Large Spark Ignition Engines and Recreational Engines (Marine and Land Based)”; Final Rule, Volume 67., No.217, November 8, 2002. These rules require a phase in of lower snowmobile emissions over the period of 2006 to 2012. In addition, the International Snowmobile Manufacturers' Association (ISMA) is developing new pass-by noise standards to replace the current wide-open throttle noise standard SAE J - 192 and J 1161. These new requirements set the stage for improvements in snowmobiles and form the basis for the Society of Automotive Engineers (SAE) Clean Snowmobile Challenge (CSC). SAE and Michigan Technological University (MTU) worked together, along with many other volunteers, to continue the SAE CSC, moving it from its original venue in Wyoming to Michigan.